九游棋牌

You are here: Home / Test Objects / Radiators and Sound Trans. Parts

Radiators and enclosures

Examples

 

 

  • Cones
  • Diaphragms
  • Membranes
  • Panels
  • Enclosures
  • Horn

Applications

 

 

  • Woofer
  • Tweeter
  • Wide-band transducer
  • Other loudspeakers and Transducers


Particularities

A force generated by the electro-mechanical transducer excites the radiator to mechanical vibration (as a rigid body or to bending or longitudinal modes). Any point of the vibrating surface (cone, diaphragm, panel) contributes as a small sound source (monopole and dipole) to the radiated sound. However, the non-vibrating boundaries (baffle, enclosure, horn, transmission line, …) affect the radiation condition (e.g. radiation impedance), sound transmission and the generated sound field. 
Most loudspeaker parts behave both ways, as a radiator and as a sound transmission part. For example, enclosure walls assumed to be rigid may break-up to bending modes and vibrate sound. The outer part of a paper cone does not vibrate at higher frequencies but behaves as a sound transmission part for the sound radiated by the dust cap. 
The shape of the surface (boundary) of the radiator and the sound transmission part directly determine the radiation and sound propagation condition. For predicting the mechanical vibration by finite element analysis, additional geometrical characteristics (e.g. thickness of the cone) and material parameters (Young’s E modulus, loss factor) are required. The properties of the materials used in paper cones and other radiators highly depend on temperature, humidity and may vary over time.
Mechanical measurements using laser sensors are very useful for measuring material parameters, performing modal analysis on radiators and predicting the sound pressure output. Note, measurements of material properties are usually performed on flat probes, and radiator is usually assessed in the final transducer.


Challenges in the Design

  • Radiators operating over a wide range as a rigid body
  • Desired bending and longitudinal vibration above break-up
  • Low amplitude of the first circumferential mode (“rocking mode”)
  • Desired radiation characteristics (directivity)
  • Sound radiating area on the radiator shrinks at higher frequencies
  • Sound pressure level and sound power level are close to accumulated acceleration level (AAL)
  • Most important characteristics:
  • Accumulated acceleration level (AAL) summarizes mechanical vibration on the radiator’s surface
  • AAL of the radial (axial-symmetrical) and circumferential vibration mode
  • On-axis SPL response, sound power response, directivity
  • Sound pressure related decomposition (in-phase, anti-phase, quadrature component)
  • Natural frequencies, loss factor, shape of vibration modes)
  • Young’s E modulus of the material
  • Loss factor or quality factor of the material

Critical Issues

  • Low modal density of the mechanical vibration on the radiator at higher frequencies
  • Low modal loss factor in the material generating high AAL at the natural frequencies
  • Small differences between in-phase component and anti-phase component indicates an acoustical cancellation problem
  • High mechanical vibration at a particular point on the radiator indicates high deformation of the local geometry causing nonlinear signal distortion


Standards

American Society for Testing and Materials
ASTM E111-04 Standard Test Method for Young's Modulus, Tangent Modulus, and Chord Modulus
九游棋牌ASTM E 756 Standard Test Method for Measuring Vibration-Damping Properties of Materials


九游棋牌most relevant measurements 

九游棋牌modules of r&d system

modules of qc system

九游棋牌3d-geometry scanning

Scanning Vibrometer System (SCN)

 

Distributed mechanical parameters
九游棋牌(mechanical vibration scanned on radiator’s surface)

Higher Modal Analysis (HMA)
Rocking Mode Analysis (RMA)
Scanning Vibrometer System (SCN) 

 

九游棋牌accumulated acceleration level (aal)

Higher Modal Analysis (HMA)
Scanning Vibrometer System (SCN)

 

modal analysis (natural frequencies, shape of modal vibration, modal loss factor)

Higher Modal Analysis (HMA)
Rocking Mode Analysis (RMA) 
Scanning Vibrometer System (SCN)

 

decomposition into radial and circumferential mode

Rocking Mode Analysis (RMA)
Scanning Vibrometer System (SCN) 

 

on-axis sound pressure amplitude response

Higher Modal Analysis (HMA)
Multi-Tone Measurement (MTON)
Scanning Vibrometer System (SCN)
Transfer Function Measurement (TRF)

Spectrum Analysis (SAN)
Sound Pressure Task (SPL)
Sound Pressure and Impedance Task (SPL-IMP)

Multi-Tone Distortion Task (MTD)

directional characteristics (directivity index, coverage angle, radiation angle, polar radiation measurement)

Higher Modal Analysis (HMA)
Scanning Vibrometer System (SCN)

 

sound power response

Near Field Scanner (NFS)
Polar Far-Field Measurement (POL)
Scanning Vibrometer System (SCN)

 

Sound pressure related decomposition
(in-phase, anti-phase, quadrature component)

Scanning Vibrometer System (SCN)

 

effective radiation area sd

Scanning Vibrometer System (SCN)

 

Material parameters
(Young’s E modulus, modal loss factor)

Higher Modal Analysis (HMA)
Material Parameter Measurement (MPM)
Rocking Mode Analysis (RMA)

 

 
乐优彩票天天红单下载 乐优彩票登入,备用,官方网址 乐优炫彩天天红单 乐优炫彩app 乐优炫彩官网 乐优彩票网址是多少 亲朋之星有手机版吗 乐优炫彩app天天红单 乐八彩票邀请码 乐优炫彩彩票app下载